plastic bearing
英 [ˈplæstɪk ˈbeərɪŋ]
美 [ˈplæstɪk ˈberɪŋ]
网络 塑料轴承
双语例句
- Plastic metal bearing alloys
卡马施锡基装饰合金塑性高锡青铜轴承合金 - The tray can also achieve full plastic bearing, but far less plastic tray convenient toughness.
这种托盘同样可以达到全塑料的承载，但是韧性方便远不如全塑料托盘。 - The Elastohydrodynamic Lubrication Analysis of Emulsion-lubricated Composite Plastic Bearing
乳化液润滑复合塑料轴承的弹流润滑分析 - Nippon duralumin plastic metal bearing alloys
日本高强度铝铜镁合金塑性高锡青铜轴承合金 - Plastic tray design is the first full plastic, bearing strength, good toughness, strong shock resistance ability.
塑料托盘最初设计是全塑料的，承载强度大、韧性好、抗冲击能力强。 - Plastic bearing surfaces all around.
四周均采用塑料支撑面。 - Precision plastic bearing plastic bearing anti-acid corrosion plastic bearings PEEK/ PI plastic bearings ( high temperature plastic bearings) Plastics and plastic bearing, spherical bearings;
精密塑料轴承耐腐蚀塑料轴承抗酸碱塑料轴承PEEK/PI塑料轴承（耐高温塑料轴承）塑料轴承座及塑料外球面轴承； - Friction and wear properties of laser melt-cladding with high-aluminum bronze powders plastic metal bearing alloys
高铝铜合金粉末激光熔覆层的摩擦磨损性能塑性高锡青铜轴承合金 - Experimental Study on Compressive Performance of Elasto Metal Plastic Bearing Pad
弹性金属塑料轴瓦压缩性能的实验研究 - Properties and Application Prospects of Elasto-Metal Plastic Sliding Bearing
弹性金属塑料轴瓦的特性及应用展望 - A set of measuring system and calibrating equipment are developed in order to measure the oil film thickness of the elastic metal plastic tile thrust bearing.
研制了一套推力轴承油膜厚度的测量系统及标定装置。 - Design of Elasto-Metal Plastic Water Pilot Bearing in Vertical Hydraulic Generator
立式水轮发电机水导弹性金属塑料轴瓦的设计 - In this paper, the properties and construction features and site test results of elasto-metal plastic sliding bearing are introduced. Applied prospects of elasto-metal plastic sliding bearing in hydrogenerator are put forward at home.
本文介绍了弹性金属塑料轴瓦的特性、结构特点和应用效果，提出了弹性金属塑料轴瓦在水力发电机中的应用前景。 - Performance and Application of Plastic Combination Liner Bearing
塑料复合衬套轴承的性能与应用 - Ultimate bearing capacity formula of Cable-Arch structure for circular& duct section is regressed by summarizing the relationship between slenderness ratio and plastic ultimate bearing capacity;
3分析长细比对索拱结构的弹塑性极限承载力的影响，在此基础上同归了圆管截面索拱结构的承载力公式。 - Injection Mould Design of Plastic Supporter of Bearing
塑料轴承保持器注射模设计 - Study on Design Parameters of Metal-base Plastic Alloy Bearing Lubricated by Water
水润滑金属基塑料轴承设计参数的研究 - The most economical section is obtained by comparing effects of cable section on the plastic ultimate bearing capacity of Cable-Arch structure;
4分析索截面改变对索&拱结构弹塑性极限承载力的影响，得出了较经济的索截面面积。 - Experimental Study on Dynamic Stretch Complex Modulus of Surface Material of Elasto Metal Plastic Bearing
塑料瓦表面材料动态复拉伸模量的实验研究 - Analysis of Plastic Bearing on Applicational Property
塑料轴承的应用特性分析 - With elastic plastic bearing as an example, the relevant theory of hydrodynamic lubrication and the effects of the grooved structure on operating characteristic are analysed.
以具有弹性的塑料轴承为例，分析相应的流体动力润滑机理以及水槽结构形式对其运行特性的影响。 - Aim at these problems hereinbefore, this paper has researched the lubrication performance of the water-lubricated plastic alloy bearing both the theory and experiment.
本文针对以上问题结合理论与实验对不同塑料合金层厚度、硬度水润滑轴承润滑性能进行了综合研究。 - On working Performance Analysis of Plastic Journal Bearing
塑料滑动轴承工作性能分析 - Engineering Verification and Field Experiment Research of Plastic Bearing Pile
塑性支承桩工程验证与现场测试试验研究 - Application of 700t Metal and Elastical Fluorite Plastic Thrust Bearing Liner made in China in Generators in Our Plant
国产700t级金属弹性氟塑料推力瓦在我厂发电机上的应用 - Elasto metal plastic bearing pad is key part of large hydraulic turbine thrust bearing and its performance being better or worse directly influences the dynamic quality of whole system running.
弹性金属塑料轴瓦是大型水轮发电机推力轴承的关键性部件，其性能的好坏直接影响到整个系统运行的动态品质。 - Slip Study of the Plastic Thrust Bearing
弹性金属塑料瓦推力轴承的滑移问题研究 - Through the contrast analysis, it is found that the introduction of the concept of effective width can be good for analysis the negative moment region in the edge of the combination frame beams on the elastic and plastic limit bearing capacity.
通过对比分析，发现有效宽度概念的引入能够较好的进行组合框架梁在端部负弯矩区的弹性和塑性极限承载力的分析。 - In working conditions, the load fluctuations, temperature gradient, stress concentration and many other factors make the rotor produce a certain amount of plastic deformation, bearing the cycle of plastic strain, led to destruction and accident.
在工作条件下产生的载荷波动、温度梯度以及应力集中等诸多因素使转子容易产生不同程度的塑性变形，并因承受塑性应变的循环作用而受到破坏，酿成事故。 - Select the appropriate coordinate system, according to the boundary condition choice of deflection approximate function, according to the structure plastic limit analysis of the theory of bending the limit condition of Component, then derived obtained under the equispaced distributed load function of plastic limit bearing capacity.
选取适当的坐标系，根据边界条件选择挠度的近似函数，按结构塑性极限分析理论中拉弯构件的极限条件，进而推导得出均布荷载作用下的塑性极限承载力。